NSNJ2000 nov-2013 application phs-if f0=265.55mhz bw=0.2mhz electrical specification: (table 1) the device characteristics are measured in the circuit shown in fig.1. (operating temperature range : -20+85oc) maximum rating: (table 2) mechanical specifications: (fig.2) package is designed as small as 3.0x3.0x1.15[mm 3 ] for smd (surface mount device) type. notice: this part is electrostatic discharge sensitive and may be damaged by improper handling. http://www.njr.co.jp/products/device/index.html http://www.njr.com/products/device/index.html table 1. electrical specifications item spec. typ. nominal center frequency (f0) 265.55mhz 3db band width (from f0) 130khz min. 275 khz insertion loss at f0 4.0db max. 3.2db ripple f0 100khz 1.2db max. 0.8db group delay time ripple f0 100khz 1.2usec max. 0.5usec f0 600khz 25db min. 30db f0 1.2mhz 40db min. 60db out of band rejection (relative to through level) f0 21.5 21.7mhz 60db min. 63db table2. maximum ratings item rating maximum input power +0dbm maximum dc voltage 7.5v operating temperature range -20~+85oc storage temperature -30~+85oc newjrc saw filter NSNJ2000
NSNJ2000 nov-2013 34 16 2 saw 5 marking (1) lot number (a) year (b) month *oct.--- x nov.--- y dec.--- z (c) date 1-9--- 0 10-19--- 1 20-31--- 2 (2) part number mark pin no. connection 1 gnd 2 gnd 3 in/out 4 gnd 5 gnd 6 out/in fig.1 measuring circuit fig.2 package dimensions (in mm) fig.3 desirable land area (in mm) in 50 out 50 0.93 0.6 0.93 3.8 3.8 2.2 1.15 1.15 110 n h lqw18a 2 p f grm18 (0.6) (0.25) (0.6) (0.53) (0.75) (0.45) 1 2 3 4 6 1. 150. 15 3. 0 0. 1 5 3. 0 0. 1 5 (a) (1) (b) (2) (1.80) 5 [2x] [4x] [4x] (c) 2 p f grm18 110 n h lqw18a 3x2 p7
NSNJ2000 nov-2013 notice 1. use this component within operating temperature range. it might not be satisfied with electrical specification without operating temperature range. when it is used less than -20oc or more than +85oc, it might be a cause of degradation or destruction of the component. even if it endures during a short time, it causes degradation of qualification. 2. when soldering iron is used, solder with the temperature at the tip of soldering iron: 350oc max., the time of soldering: 10 seconds max., the power of soldering iron: 30w max.. 3. notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. as rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. confirm that there are not any influence for qualification to this component in mounting on pcb when this component is cleaned. 6. as it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. and do not transport this component with bare hand. 7. as it might be a cause of degradation or destruction to apply d.c. voltage between each terminal, apply d.c. voltage 7.5v max. in actual circuit. note 1. this specification specifies the quality of this component as a single unit. make sure that this component is evaluated and confirmed against this specification when it is mounted to your products.
NSNJ2000 nov-2013 s21 0 1 2 3 4 5 6 7 8 9 10 265.05 265.55 266.05 frequency [mhz] insertion loss [db] s21 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 265.05 265.55 266.05 frequency [mhz] group delay [nsec] s21 0 5 10 15 20 25 30 35 40 45 50 264.05 265.55 267.05 frequency [mhz] insertion loss [db] s21 0 10 20 30 40 50 60 70 80 90 100 240.55 265.55 290.55 frequency [mhz] insertion loss [db] s22 s11
|
